Features
- Bottom Plate: 2mm
- ARM: 3mm
- Flight Controller: Kakute F7 mini V3
- ESC: Tekko32 F3 4in1 35A mini ESC
- Motor: F1404 KV3800
- Propeller: Gemfan Hurricane 4023-3
- Buzzer included.
- Wheelbase: 180mm
- Battery plug: XT30
- Recommend battery: 650~850mAh 4s
Analog VTx version
- 5.8G VTx: Atlatl HV Micro
- Foxeer Lollipop 3 2.5Dbi Stubby Omni FPV Antenna
- FPV camera: 1200TVL Foxeer Micro Razer FPV Camera
- Weight:166g(without battery)
CADDX FPV version
- VTx: Caddx FPV Digital HD Camera Nebula Nano Kit
- Weight:173g(without battery)
Specifications
| Flight Controller: Kakute F7 mini V3 |
- MCU: STM32F722RET6 32-bit processor,216MHz, 256Kbytes RAM, 512Kbytes Flash
- IMU: MPU6000 (SPI)
- Barometer: BMP280
- USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
- 5hardware UARTS (UART1,2,3,4,6)
- Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
- Onbord 16Mbytes for Blackbox logging
- 5V Power Out: 1.0A max
- 3.3V Power Out: 0.2A max
- Dimensions: 30x30mm
- Mounting Holes: Standard 20mm square to center of holes
- Weight: 4g
|
ESC:
Tekko32 F3 4in1 35A mini |
- F3 MCU, double the speed of F051, the MCU works at 108Mhz
- 32bit ESC with BLHELI32 firmware
- Supports 3-6S lipo input
- Default PWM output 96K
- Amperage meter scale ratio has been adjusted to 185.
- PWM input, TLM supported
- Voltage output (VBAT)
- NO output BEC
- Supports oneshot / Multishot / Dshot PWM
- Supports damped light
- Ext. cap needed for 6s (1000uf 35v for 6s usage.)
- Mounting holes: 20x20mm(M3)
- Size:32 x 38 mm
- Weight: 8g
|
Analog version：
5.8G VTx: Atlatl HV Micor |
- Output Power: 0.5mW (pit mode), 25mW, 200mW, 500mW, 800mW
- Audio: 6.5 MHz Mono
- Protocol: smart audio2.0
- Antenna Connector: MMCX
- Input Voltage: 7 to 28 volts (2-6S LiPo)
- Dimensions: 30x26mm
- Mounting Holes: 20x20mm (M3)
- Weight: 3.6g
|
HD version：
CDDX FPV Vista Kit |
- Dimensions: Module: 30.45 x 29 x 13mm
- Weight: 29g (inc. camera); Module: 19g
- Antenna Connector: u.FL
- Operating Frequency: 5.725-5.85GHz
- Transmitter Power (EIRP)
- FCC/SRRC/MIC: <20dBm; CE: <14dBm
- I/O Interface: USB-C, IPEX, 3-in-1 Port
- Min. Latency: Low Latency Mode (720p 120fps): 21-28ms
- High-Quality Mode (720p 60fps): 30-40ms
- Max Transmission Distance: FCC/SRRC: 4km; CE: 0.7km
- Input Power: 7.4-26.4v
- Nebula Nano Camera
Sensor: 1/3″ CMOS; Lens: 2.1mm; Shutter: Rolling Shutter; FOV: 150°;14x14x21mm
When powered on, connected the vista kit to your computer and run DJI ASSISTANTTM 2 for activation.
Download DJI Assistant 2 at https://www.dji.com/fpv/downloads |
Includes:
Includes:
- 1x Kopis FPV racing drone
- 8x 4023-3 Propeller
- 1x Battery strap(installed)
- 1x Naked GoPro camera mount
